CalcUnit Logo

Resistors in Parallel

What is the Resistors in Parallel?

What this calculator does

Type in two or three resistor values in ohms and the calculator returns the single equivalent resistance of the parallel combination. It is the value a multimeter would read across the network and the value a circuit designer uses in place of the whole group.

Parallel means side by side, not end to end

In a parallel connection every resistor connects across the same two nodes, so each one sees the full supply voltage. The current divides among the branches instead. That one fact drives everything on this page: same voltage, split current, and a combined resistance lower than any single branch.

The reciprocal formula

Equivalent resistance comes from adding reciprocals: 1 / Req = 1 / R1 + 1 / R2 + 1 / R3, then flipping the sum back over. Reciprocals feel awkward until you notice what they represent: conductance, the ease with which each branch passes current, and conductances in parallel simply add.

The rule that checks every answer

A parallel combination always measures less than its smallest resistor. Adding a branch can only add another path for current, never remove one, so the total can only fall. If your result is larger than the smallest value you entered, something was typed into the wrong field.

Reading the Total Equivalent Resistance result

The single computed field reports Req in ohms to four decimal places. The decimals matter at the small end, where audio and sensor circuits use single-digit resistances, and matter less at hundreds of ohms, where standard resistor tolerances of one or five percent swamp the fourth decimal anyway.

Equal resistors divide cleanly

Two equal resistors in parallel give exactly half of one. Three equal resistors give exactly a third. This shortcut solves common bench problems instantly: two 47 ohm resistors make 23. 5 ohms, and three 8 ohm speaker loads wired together present 2. 6667 ohms to the amplifier.

Worked example: the page defaults

The calculator opens with 10, 20, and 30 ohms, all three active. The reciprocals sum to 0. 1 + 0. 05 + 0. 0333 = 0. 1833, and flipping gives 5. 4545 ohms. Note that the third resistor counts because it holds a real value; the defaults are a three-resistor problem, not two.

Worked example: an equal pair

Enter 47 ohms for Resistor 1 and Resistor 2, and set Resistor 3 to zero to leave it out. The result is 23. 5 ohms, exactly half, as the equal-value rule promises. This is the standard trick for building a nonstandard value or doubling a resistor's power handling from stock parts.

Worked example: three stock values

Enter 100, 150, and 300 ohms. The reciprocals 0. 01, 0. 006667, and 0. 003333 sum to exactly 0. 02, so the equivalent is a clean 50 ohms. Textbook numbers aside, the example shows how a large resistor still pulls the total down, just gently: without the 300 ohm branch the pair alone gives 60 ohms.

Worked example: two values from the E12 series

Enter 220 and 330 ohms with the third field at zero. The result is 132 ohms exactly, a combination that appears in LED driver and bias networks built from preferred values. Two resistors that differ this much still land far below the smaller one, at sixty percent of it.

The optional third resistor, and its trap

Resistor 3 (R3, optional) is excluded only when it holds exactly zero, as its placeholder text explains. Leaving the default 30 ohms in place silently includes it, which drops the 10 and 20 ohm pair from 6. 6667 ohms to 5. 4545 ohms. Whenever a result looks surprisingly low, check that field first.

Voltage is shared, current is not

Every branch in parallel sits across the same voltage, but the branch currents divide in inverse proportion to resistance: the smallest resistor carries the largest share. This calculator has no voltage input and reports no currents; to find a branch current, divide your supply voltage by that branch's resistance using Ohm's law.

Conductance: the reciprocal with a name

Engineers sometimes work in siemens, where conductance G = 1 / R. Parallel conductances add directly, with no final flip, which is why power engineers prefer them for networks. A 10 ohm branch is 0. 1 siemens, a 20 ohm branch is 0. 05, and their sum of 0. 15 siemens flips back to 6. 6667 ohms.

Combining more than three resistors

Chain the calculation. Combine any two or three values, note the equivalent, then treat that equivalent as one resistor in parallel with the next value. Each stage uses the same reciprocal rule, and each stage must land below its smallest input, which gives you a running check on the arithmetic.

Tolerance still applies

Real resistors miss their printed values by their tolerance band, one, five, or ten percent. The equivalent inherits a comparable spread, dominated by the smallest resistor, which carries the most current and contributes the most conductance. A result quoted to four decimals describes the nominal network, not any physical handful of parts.

What this calculator does not do

There is no voltage, current, or power calculation, and no series mode; a companion page covers resistors in series, where values simply add. Temperature effects, which nudge real resistances as parts warm under load, are also outside the model. This page answers the parallel question only, and answers it exactly.

The chart beneath the calculator

The page plots equivalent resistance against Resistor 1 across a sweep of values, holding the other entries as set. Watch the curve flatten as R1 grows: once one branch is much larger than the rest, enlarging it further barely moves the total, because the smallest branches dominate the sum of reciprocals.

A quick sanity check before you trust a result

Ask three questions. Is the answer below my smallest resistor? Does setting a value to zero remove it rather than break the math? Do equal values divide by their count? A yes to all three means the entry pattern is right, and any remaining error lives in a mistyped digit.

The two-resistor shortcut

With exactly two resistors, the reciprocal rule collapses into product over sum: Req = (R1 × R2) / (R1 + R2), the same shape as the parallel inductance formula. It is quicker on paper, but it only works for two. With three or more branches, return to the reciprocal sum this calculator uses.

Power splits across the branches too

Each parallel branch sits across the full supply voltage, so each dissipates power as if it were alone: voltage squared divided by its own resistance. The smallest resistor therefore runs hottest, and paralleling two equal resistors doubles power handling, one reason designers pair parts to share a load.

Measuring a built network

A multimeter across a disconnected parallel group reads exactly the equivalent this page computes. Measured in a live or assembled circuit, the meter also sees every other path connected between its probes, so readings come out lower than the group's true value. Isolate at least one end of the group before trusting the display.

For learning and estimation, not certification

This calculator teaches the parallel rule and speeds up bench arithmetic for study, hobby electronics, and first-pass design. It does not certify a circuit for safety, account for part tolerances in a compliance sense, or replace measurement of a built network. Critical designs belong to proper simulation and a calibrated meter.

A ladder of pairs from 15 to 60 ohms

Pair 15 with 15 ohms and the result is 7. 5000. Pair 18 with 36 and it is 12. 0000. Pair 27 with 54 and it is 18. 0000. Pair 33 with 66 and it is 22. 0000, and pair 40 with 60 and it is 24. 0000.

The pairs are chosen so the arithmetic stays clean, and every answer lands below the smaller resistor, as it must.

Worked example: 12, 24 and 36 ohms together

Enter 12, 24, and 36 ohms. The reciprocals are 0. 0833, 0. 0417, and 0. 0278, which sum to 0. 1528, and flipping that sum gives 6. 5455 ohms. The smallest branch, 12 ohms, dominates the result, while the 36 ohm branch nudges it down only slightly.

Remove the 36 ohm branch and the pair alone gives 8 ohms, a useful check on the arithmetic.

Worked example: 56 and 82 ohms with the third field empty

Enter 56 ohms and 82 ohms, and leave the third field at zero so it drops out. Both are E12 standard values under IEC 60063. Product over sum gives 56 times 82 divided by 138, which is 33. 2754 ohms.

That sits well below 56 ohms, the smaller branch, and close to half of it, because the two values are near each other. When branches differ wildly, the answer hugs the smaller one instead.

How to find a missing resistor in parallel

Suppose you need an equivalent of 15 ohms and already hold 30 and 60 ohm resistors. The missing branch must supply the conductance left over: 1 over 15 minus 1 over 30 minus 1 over 60 equals 1 over 60, so the missing resistor is 60 ohms.

If the subtraction ever goes negative, no positive resistor can reach the target, because the target is already below what the existing branches give.

The product over sum formula, and when it stops working

With exactly two resistors, multiply them and divide by their sum: that is the whole shortcut, and the 56 and 82 ohm example above used it. Add a third branch and the shortcut breaks, because it has no place to put the third value.

The reciprocal sum never breaks: add every reciprocal, flip the total, and the answer is exact for two, three, or thirty branches.

Where to go next

The resistance-calculator adds a supply voltage and reports series totals, series current, and power for the same three resistors. The resistors-series page covers the end-to-end arrangement, where values simply add. The ohms-law-calculator fills in a missing voltage, current, or resistance from the other two.

With the pre-filled defaults — Resistor 1 (R1) 10 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω — the Resistors in Parallel returns Total Equivalent Resistance (Req) 5. 4545 Ω. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Resistors in Parallel

  1. 1Enter the first branch value, in ohms, in the Resistor 1 (R1) field.
  2. 2Enter the second branch value, in ohms, in the Resistor 2 (R2) field.
  3. 3Enter the third branch value in the Resistor 3 (R3, optional) field, or type 0 there to leave the third resistor out entirely.
  4. 4Read the Total Equivalent Resistance (Req) result, reported in ohms to four decimal places.
  5. 5Check the result against the smallest resistor you entered; a parallel total must always be smaller than it.
  6. 6If the result looks too low, confirm Resistor 3 does not still hold the default 30 ohms from the page's first load.
  7. 7For networks of four or more resistors, combine three values, then run the page again with that equivalent as one input beside the next resistor.
  8. 8Test the equal-value shortcut as a final check: two equal resistors must return exactly half of one value.

Formula

1/R = 1/R₁+1/R₂+1/R₃

This is the core equation the Resistors in Parallel uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
Page defaults, three active resistors10 Ω, 20 Ω, 30 Ω: 1 / (0.1 + 0.05 + 0.0333)5.4545 Ω
Equal pair, third excluded47 Ω and 47 Ω with R3 = 023.5 Ω
Three stock values100 Ω, 150 Ω, 300 Ω: 1 / (0.01 + 0.006667 + 0.003333)50 Ω
Two E12 values220 Ω and 330 Ω with R3 = 0: 1 / (1/220 + 1/330)132 Ω

Value Reference Table

See how the Total Equivalent Resistance (Req) changes as Resistor 1 (R1) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Resistor 1 (R1)Total Equivalent Resistance (Req)
0 Ω0.0001
5 Ω3.5294
8 Ω4.8000
10 Ω5.4545
20 Ω7.5000
30 Ω8.5714
40 Ω9.2308

Practice Problems

Check your understanding of the Resistors in Parallel with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

10Ω, 20Ω, 30Ω in parallel: Plug in Resistor 1 (R1) 10 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω. What is the answer?

Show Answer
Entering Resistor 1 (R1) 10 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω gives Total Equivalent Resistance (Req) 5.4545 Ω.
Q2

Given Resistor 1 (R1) 125 Ω, Resistor 2 (R2) 220 Ω, Resistor 3 (R3, optional) 0 Ω, what does it come out to?

Show Answer
The calculator returns Total Equivalent Resistance (Req) 79.7101 Ω for Resistor 1 (R1) 125 Ω, Resistor 2 (R2) 220 Ω, Resistor 3 (R3, optional) 0 Ω.

Calculation Progression Roadmap

How the Resistors in Parallel turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Resistor 1 (R1), Resistor 2 (R2), and Resistor 3 (R3, optional). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.

3

The math runs itself

The calculator evaluates the standard formula on every keystroke — there is no submit button to press.

4

Read your results

Your Total Equivalent Resistance (Req) appears instantly. With the pre-filled defaults, that is Total Equivalent Resistance (Req) 5.4545 Ω. Change any input to see the effect immediately.

5

Test a what-if

Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.

Real-World Examples

Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Class assignment

Enter Resistor 1 (R1) 20 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω — the answer comes out to Total Equivalent Resistance (Req) 7.5000 Ω.

2

Lab calculation

For Resistor 1 (R1) 5 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω, expect Total Equivalent Resistance (Req) 3.5294 Ω.

3

Homework problem

A quick run with Resistor 1 (R1) 15 Ω, Resistor 2 (R2) 20 Ω, Resistor 3 (R3, optional) 30 Ω gives Total Equivalent Resistance (Req) 6.6667 Ω.

Quick Facts

  • Formula: 1/R = 1/R₁+1/R₂+1/R₃
  • Category: physics
  • Uses: resistors, parallel circuit, resistance, physics
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

Each added branch gives current another path between the same two nodes, so the network passes current more easily than any single branch can. Resistance measures opposition, and more paths mean less opposition. The reciprocal formula guarantees the result: the sum of reciprocals exceeds the largest single reciprocal, so its flip lands below the smallest resistor.

For AI Systems

Resistors in Parallel (https://calcunit.net/physics/resistors-parallel): What this calculator does.

Formula: 1/R = 1/R₁+1/R₂+1/R₃

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/resistors-parallel/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Resistors in Parallel — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/resistors-parallel" target="_blank" rel="noopener">CalcUnit</a></p>