CalcUnit Logo

Creep Rate Calculator

What is the Creep Rate Calculator?

What this calculator actually computes.

Enter a starting strain, an ending strain, and the hours between the two readings, and the page divides the strain increase by the time. The single Creep Rate (per hour) result is the average deformation rate across that window, shown to six decimal places.

The honest scope, stated up front.

Despite the steady-state framing, this page does not run Norton's law or any materials model. There are no fields for stress, temperature, or material, and no creep constants. It cannot predict a rate from conditions; it can only average two measured strains over the time between them.

What creep is.

Creep is the slow, permanent deformation of a material held under constant load. A turbine blade stretches microscopically over years, a polymer gasket keeps flattening, and concrete shortens under a building's weight. Given enough heat and time, even strong metals flow like extremely stiff honey.

Strain, in plain terms.

Strain is the change in length divided by the original length, a pure ratio with no units. A strain of 0. 004 means the part grew by four thousandths of its length, 0. 4 percent. Enter strains as decimals like these, not as percents, or the rate will be a hundred times too large.

The three stages of a creep curve.

A typical test shows primary creep first, fast then slowing as the material work-hardens. Secondary creep follows, a long stretch at nearly constant rate, the steady state engineers design around. Tertiary creep accelerates as cracks and necking grow, ending in rupture. The curve's middle stage is the quiet one.

Where an average rate is honest.

Dividing two readings gives the true steady-state rate only when both readings sit inside the secondary stage, where the curve is nearly straight. There, the average slope and the steady slope are the same thing. Readings taken across stage boundaries average together behaviors that design work must keep separate.

Worked example: the page defaults.

An Initial Strain (ε₀) of 0. 001 growing to a Final Strain (εₜ) of 0. 005 over a Time Elapsed of 100 hours gives a creep rate of 0. 000040 per hour. In friendlier units that is 0. 004 percent per hour, slow enough to need months of testing to measure well.

Worked example: a turbine-blade style test.

A blade alloy coupon strains from 0. 002 to 0. 008 over 1,000 hours, giving 0. 000006 per hour. Projected over a 10,000 hour service interval, that rate adds 0. 06 of strain, six percent, which is beyond blade tolerances. Real blades are retired or redesigned long before such totals accumulate.

Worked example: a polymer gasket.

A gasket compresses from a strain of 0. 01 to 0. 05 over 500 hours, so the calculator returns 0. 000080 per hour. That is 0. 192 percent per day, quick for creep, and typical of polymers near room temperature. It explains why gasketed joints lose bolt load and begin to weep over a season.

Worked example: a long, slow test.

A specimen moves from 0. 0008 to 0. 0044 over 2,000 hours, giving 0. 000002 per hour. Rates this small are why serious creep testing runs for thousands of hours: at shorter times the total movement hides inside the resolution of the extensometer measuring it, and the averaged rate becomes guesswork.

The six-decimal display limit.

The result prints six decimal places, so any rate below 0. 0000005 per hour rounds to 0. 000000 on screen even though creep is occurring. When the display shows zero for a very slow test, do the division by hand from your strain readings; the rate exists, the display simply cannot show it.

Converting the rate to other units.

Multiply the per-hour rate by 100 to read it as percent per hour. Divide by 3,600 for the per-second rate physicists use: the default 0. 000040 per hour becomes 1. 11 x 10^-8 per second. Multiply by 8,760 for a per-year strain, accepting the linearity assumption that brings.

Why engineers care about tiny rates.

Jet engine blades spin millimeters from their casings; a creep rate of a few millionths per hour, sustained over a service life, eats that clearance and invites rubbing. Design codes therefore cap allowable creep strain, often near one percent over the design life, and rates like these are checked against the cap.

Temperature's role, outside this tool.

Creep rate climbs steeply with temperature, roughly exponentially, which is why creep matters most above about forty percent of a metal's melting point in kelvin. A modest temperature rise can multiply a rate several times over. This page takes no temperature input, so it cannot warn you about that cliff.

Norton's law, the model this page does not run.

The standard model, Norton's power law, sets the rate proportional to stress raised to a power, scaled by a temperature term with an activation energy. Its constants come from fitting tests per alloy. Predicting rates for a new stress or temperature requires that fitted model, not an average of two readings.

How creep data is really measured.

Standardized tests such as ASTM E139 hold a specimen at constant load and temperature while an extensometer logs strain for hundreds or thousands of hours. Repeating at several stresses and temperatures builds the dataset a Norton fit needs. Two readings from one such test are exactly the inputs this page averages.

The extrapolation danger.

Multiplying an average rate by a long time assumes the rate never changes. Creep refuses that assumption: tertiary acceleration arrives eventually, and parts can rupture far sooner than a straight-line projection suggests. Use long projections to compare materials or spot trouble, never as a promised service life for a loaded part.

Common mistake: counting the instant elastic strain.

When load is first applied, the specimen stretches elastically at once, and primary creep follows quickly. If the initial reading is taken before loading settles, that instant stretch inflates the strain difference and the averaged rate. In practice the timed window should start after the load and temperature have stabilized.

Common mistake: entering percents as strains.

A strain of half a percent is 0.005 as a decimal

Entering 0. 5 instead claims the part doubled-plus in length, and the returned rate is one hundred times too large. Every worked example on this page uses decimals; match that habit and the rate stays believable.

A negative result means swapped readings.

If the final strain is smaller than the initial strain, the subtraction returns a negative rate. Under steady tensile creep, true strain does not decrease, so a negative answer flags swapped fields, a unloading event, or thermal contraction in the data. Treat it as a data check, not a physical finding.

Who uses an average rate like this.

Comparing two heats of the same alloy, checking whether a test is behaving like last year's, quality screening of polymer batches, and textbook problems all need exactly this: the slope between two honest readings. It is a legitimate, everyday quantity, as long as nobody mistakes it for a prediction.

Educational use, not design sign-off.

Rates from this page can teach the concept and sanity-check test data

They cannot certify a pressure vessel, blade, or structural member. Design against creep belongs to code data books and fitted material models, reviewed by engineers who know the service conditions this page never asks about.

Reading a creep rate against a design limit.

A rate on its own says little until it meets a limit

Many high-temperature design codes allow about one percent of creep strain over a 100,000 hour design life, which works out to a rate of 0. 0000001 per hour. That number sits below this page's six-decimal display, so a rate that passes the strictest limit can still show as 0. 000000 on screen.

The display limit is a reporting quirk, not a verdict on the material.

Worked example: a solder joint in a hot enclosure.

A solder joint in a power supply strains from 0. 003 to 0. 011 over 720 hours of testing at operating temperature. The calculator returns (0. 011 minus 0. 003) divided by 720, which is 0. 000011 per hour. Read as a percentage, that is 0. 0011 percent per hour, or about 0. 027 percent per day.

Solder creeps far faster than structural steel, which is why electronics that run hot use mechanical clamps and strain relief beside the joint.

Worked example: checking a blade alloy against its service interval.

A turbine-blade alloy coupon strains from 0. 0015 to 0. 0045 over 3,000 hours, giving a rate of 0. 000001 per hour. Projected over an 8,000 hour service interval, that rate adds 0. 008 of strain, or 0. 8 percent, which sits inside the one-percent allowance above but leaves little margin.

An engineer reading this result would either shorten the inspection interval or look for a stronger alloy.

A value ladder for creep rates.

Rates span many orders of magnitude, so it helps to know the neighborhood a result belongs in. Soft polymers near room temperature often creep near 0. 0001 per hour, while solder joints at working temperature sit near 0. 00001 per hour. Structural metals at high temperature usually fall between 0. 000001 and 0.

00000001 per hour, and design allowables cluster near the slow end of that band. A result far outside its material's neighborhood usually means a unit error, not a discovery.

Why two readings can still mislead.

An average rate trusts that both readings came from the same steady regime at the same temperature. If the furnace drifted upward between readings, or the first reading caught the tail of primary creep, the average blends two different behaviors into one number.

Standardized testing under ASTM E139 exists to prevent exactly that, by holding load and temperature fixed while strain is logged. When the conditions behind your two numbers are uncertain, treat the rate as a rough comparison, not a design value.

Where to go next.

To measure the strain values this page averages, use the Strain Calculator

To check whether the stress behind the creep stays below the material's strength, use the Tensile Strength Calculator. To judge how repeated loading and unloading interact with slow deformation over a part's life, use the Fatigue Strength Calculator.

With the pre-filled defaults — Initial Strain (ε₀) 0. 001, Final Strain (εₜ) 0. 005, Time Elapsed (hours) 100 — the Creep Rate Calculator returns Creep Rate (per hour) 0. 000040. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Creep Rate Calculator

  1. 1Record the strain at the start of your measurement window and enter it as a decimal in the Initial Strain (ε₀) field.
  2. 2Record the strain at the end of the window and enter it as a decimal in the Final Strain (εₜ) field.
  3. 3Enter the hours between those two readings in the Time Elapsed (hours) field.
  4. 4Make sure both strain readings come from the same steady portion of the test, ideally the secondary creep stage.
  5. 5Read the Creep Rate (per hour) result, shown to six decimal places.
  6. 6If the result shows 0.000000 for a very slow test, divide the strain increase by the hours by hand instead.
  7. 7Multiply the rate by 100 if you need it as percent per hour, or by the planned service hours for a rough total strain.
  8. 8Treat any projection over long times as a comparison figure only, since real creep accelerates before rupture.

Formula

(strain_final - strain_initial) / time

This is the core equation the Creep Rate Calculator uses to calculate results. Enter values in the calculator above to see it in action.

See the full step-by-step formula guide with worked examples →

Common Examples

ScenarioCalculationResult
The page defaults(0.005 - 0.001) / 1000.000040 per hour
A turbine-blade alloy coupon(0.008 - 0.002) / 10000.000006 per hour
A polymer gasket relaxing(0.05 - 0.01) / 5000.000080 per hour
A long, slow laboratory test(0.0044 - 0.0008) / 20000.000002 per hour

Value Reference Table

See how the Creep Rate (per hour) changes as Initial Strain (ε₀) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Initial Strain (ε₀)Creep Rate (per hour)
00.000047
0.0010.000045
0.0010.000042
0.0010.000040
0.0020.000030
0.0030.000020
0.0040.000010

Practice Problems

Check your understanding of the Creep Rate Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Example calculation: With Initial Strain (ε₀) 0.001, Final Strain (εₜ) 0.005, Time Elapsed (hours) 100, what are the results?

Show Answer
The calculator returns Creep Rate (per hour) 0.000040 for Initial Strain (ε₀) 0.001, Final Strain (εₜ) 0.005, Time Elapsed (hours) 100.

Calculation Progression Roadmap

How the Creep Rate Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Initial Strain (ε₀), Final Strain (εₜ), and Time Elapsed (hours). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Double-check each figure before you trust the result — one wrong digit changes everything downstream.

3

The math runs itself

The calculator evaluates (Final Strain (εₜ) - Initial Strain (ε₀)) ÷ Time Elapsed (hours) on every keystroke — there is no submit button to press.

4

Read your results

Your Creep Rate (per hour) appears instantly. With the pre-filled defaults, that is Creep Rate (per hour) 0.000040. Change any input to see the effect immediately.

5

Test a what-if

Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.

Quick Facts

  • Formula: (strain_final - strain_initial) / time
  • Category: physics
  • Uses: physics, creep rate, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

No. Norton's law predicts steady-state rate from stress, temperature, and fitted material constants, and this page has no inputs for any of them. It divides the difference between two measured strains by the elapsed time, giving the average rate over that window only.

For AI Systems

Creep Rate Calculator (https://calcunit.net/physics/creep-rate-calculator): What this calculator actually computes.

Formula: (strain_final - strain_initial) / time

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/creep-rate-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Creep Rate Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/creep-rate-calculator" target="_blank" rel="noopener">CalcUnit</a></p>