CalcUnit Logo

Radioactive Calculator

What is the Radioactive Calculator?

What this calculator does

Enter a sample's initial activity in becquerels, its half-life, and an elapsed time, and this calculator returns the activity remaining, the decay constant, and the percentage of the sample that has decayed. It is built for physics students and laboratory trainees learning how measurable activity fades with time.

Activity: the becquerel, in plain terms

One becquerel is one nuclear decay per second. It is named for Henri Becquerel, who discovered radioactivity in 1896. American references often use the older curie instead: one curie equals 3. 7 x 10^10 becquerels, the activity of about a gram of radium.

The halving rule behind every output

Each half-life that passes cuts the activity exactly in half, whatever its size. The calculator applies that as an exponential: activity remaining equals initial activity times 0. 5 raised to elapsed time divided by half-life. Fractional exponents handle partial half-lives smoothly and exactly.

The decay constant, the third output

The decay constant, lambda, equals the natural logarithm of 2 divided by the half-life. It is the fraction of the remaining sample expected to decay per unit time, so a large lambda means a fast, short-lived sample and a small one means slow decay.

Fraction decayed, the percentage output

Fraction Decayed reports how much of the original activity is gone, as a percent: one hundred times one minus the ratio of remaining to initial activity. At exactly one half-life it reads 50 percent. It and the surviving fraction always sum to 100.

Worked example: an eight-day half-life

Enter initial activity 4000 Bq, half-life 8 days, and elapsed time 16 days, close to iodine-131's real 8. 02 day half-life. Two full half-lives pass, so activity remaining is 1000 Bq. The decay constant is 0. 0866 per day, and the fraction decayed is 75 percent.

Worked example: half of a half-life

Enter 12,000 Bq, a half-life of 14 days, and an elapsed time of 7 days. Activity remaining is 8485. 2814 Bq, the decay constant 0. 0495 per day, and the fraction decayed 29. 2893 percent. Halfway through a half-life, noticeably less than half the sample is gone.

Worked example: three half-lives out

Enter 250 Bq, a half-life of 30 days, and an elapsed time of 90 days. Three halvings leave one eighth standing: activity remaining 31. 25 Bq, decay constant 0. 0231 per day, fraction decayed 87. 5 percent. Long tails like this are why storage times run to many half-lives.

Worked example: a short-lived source

Enter 500,000 Bq, a half-life of 2 days, and an elapsed time of 5 days. Activity remaining is 88,388. 3476 Bq and the fraction decayed is 82. 3223 percent, with a decay constant of 0. 3466 per day. Two and a half half-lives erase more than four fifths.

Why the first half-life removes the most

Decay removes a fixed fraction per unit time, not a fixed amount. The first half-life of a 12,000 Bq sample destroys 6000 Bq of activity; the next destroys only 3000. Equal clocks, shrinking bites, because each bite is a share of what remains.

Why activity never quite reaches zero

The exponential curve approaches zero without touching it. After ten half-lives about 0. 0977 percent of the original activity remains, one part in 1024. In practice a sample becomes indistinguishable from background radiation long before the mathematics runs out of halvings.

Time units must match each other

Both time fields are labeled in days, and the decay constant then comes out per day. The mathematics only requires consistency: enter a half-life in hours and an elapsed time in hours and every output stays correct, with the decay constant read as per hour instead.

Activity is not a count of atoms

Activity equals the decay constant times the number of undecayed atoms, so the same 1000 Bq can be a speck of a short-lived isotope or a large mass of a long-lived one. This calculator tracks the measurable rate, not the inventory of atoms behind it.

Activity is not dose, and not a safety verdict

A becquerel figure counts decays per second. It says nothing by itself about the energy carried, the radiation type, or what any person absorbs, which is what dose units such as the sievert describe. Treat this page as educational physics, never as a safety assessment.

Where half-lives come from

Half-lives are measured laboratory constants, published in evaluated nuclear data tables such as those maintained by the National Nuclear Data Center at Brookhaven National Laboratory. Carbon-14's 5730 years and iodine-131's 8. 02 days come from that literature, not from this calculator's arithmetic.

Common mistake: thinking decay is linear

After one half-life a sample is half gone, so it is tempting to say it will be fully gone after two. It will not: two half-lives leave 25 percent, three leave 12. 5 percent. Linear thinking is the single most common error in first decay calculations.

Common mistake: mixing time units

A half-life of 8 days against an elapsed time entered as 24 hours silently compares days to hours and produces nonsense that still looks like a number. Convert both to the same unit before entering them, and the decay constant's unit follows that choice.

Precision: four decimal places

Outputs carry four decimal places. The displayed decay constant is rounded, so rebuilding the activity from the printed lambda instead of the exact ln 2 ratio introduces a small drift. For exact work, trust the Activity Remaining output, which is computed before any display rounding.

What this calculator does not do

It follows a single isotope decaying away. It does not model decay chains, where a daughter product is itself radioactive and grows in as the parent fades, and it handles no branching ratios, shielding, geometry, or dose. Those need dedicated nuclear-engineering tools and measured data.

The page defaults, walked through slowly

The calculator opens with 1000 Bq, a half-life of 8 days, and an elapsed time of 24 days. Three half-lives pass, so the activity falls to 125 Bq, one eighth of the start. The decay constant reads 0. 0866 per day and the fraction decayed 87. 5 percent. Confirm those by hand first.

Mean lifetime: the constant's other face

One division turns the decay constant into the mean lifetime, the average time an atom survives before decaying: tau equals 1 divided by lambda, or 1. 4427 times the half-life. For the eight-day case that is 11. 5416 days. The calculator does not print it, but it is hiding inside the lambda output.

Background radiation is the practical floor

Decay curves end not at zero but at the background count that surrounds us. A human body itself carries roughly 4000 becquerels from potassium-40 alone. Once a sample's activity fades near the levels of ordinary surroundings, no counter can separate it from the noise, whatever the formula says.

Reading the three outputs together

Two checks confirm a sensible run. The fraction decayed plus the surviving share, activity divided by initial activity, must total 100 percent. And when elapsed time equals the half-life exactly, Activity Remaining must be precisely half of what you entered.

A ladder of halvings for one sample

Start with 6400 becquerels and a half-life of 5 days, with a decay constant of 0. 1386 per day. After 5 days, one half-life, 3200. 0000 becquerels remain. After 10 days, 1600. 0000 remain. After 15 days, three half-lives, 800. 0000 remain. After 20 days, four half-lives, 400. 0000 remain.

Each step halves what came before, never subtracting a fixed amount.

Worked example: one and a half half-lives

Take 800 becquerels with a half-life of 6 days and wait 9 days. That is 1. 5 half-lives, so the activity is 800 times 0. 5 to the power 1. 5, which is 282. 8427 becquerels. The decay constant is the natural log of 2 divided by 6, or 0. 1155 per day. The fraction decayed is 64.

6447 percent, more than half gone before two half-lives have passed.

Worked example: seven days with a four-day half-life

Take 1500 becquerels with a half-life of 4 days and wait 7 days. That is 1. 75 half-lives, so the activity is 1500 times 0. 5 to the power 1. 75, which is 445. 9527 becquerels. The decay constant is 0. 1733 per day, and the fraction decayed is 70. 2698 percent.

This is how to calculate activity after half-life when the elapsed time is not a whole number of half-lives.

How much remains after 3 half-lives, exactly

After one half-life half the sample remains, after two a quarter, and after three half-lives exactly one eighth, or 12. 5 percent. That is why the ladder above falls from 6400 to 800 becquerels in three steps. The pattern is the same for any starting activity and any half-life, which makes it a fast mental check on any calculator result.

Why radioactive decay is not linear

Is radioactive decay linear? It is not. A linear fall would remove the same number of becquerels every day, reaching zero on a schedule. Real decay removes the same fraction instead, so the daily loss shrinks as the sample shrinks.

The first half-life of a 6400 becquerel sample removes 3200 becquerels, while the fourth removes only 400, and the curve never quite touches zero.

Where to go next

For the clock behind decay, open the Half-Life Calculator at half-life-calculator, which works the same half-life mathematics from the time side. The Decay Calculator at decay-calculator offers a second route through the same formulas.

To see how activity relates to the dose people actually absorb, try the Radiation Calculator at radiation-calculator, keeping in mind that becquerels and sieverts measure different things.

With the pre-filled defaults — Initial Activity 1,000Bq, Half-Life 8days, Elapsed Time 24days — the Radioactive Calculator returns Activity Remaining 125. 0000Bq, Decay Constant 0. 0866/day, Fraction Decayed 87. 5000%. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Radioactive Calculator

  1. 1Enter the sample's starting count rate in the Initial Activity field, in becquerels: one becquerel is one decay per second.
  2. 2Enter the isotope's half-life in the Half-Life field, using the published value for your isotope, in days as the field is labeled.
  3. 3Enter how much time has passed in the Elapsed Time field, in the same unit as the half-life.
  4. 4Read Activity Remaining for the count rate the sample has now, in becquerels.
  5. 5Read Decay Constant for the per-day decay rate, lambda, which is larger for shorter-lived samples.
  6. 6Read Fraction Decayed to see what percentage of the original activity has disappeared.
  7. 7Check the run: at an elapsed time equal to the half-life, Activity Remaining should be exactly half of Initial Activity.
  8. 8Re-run with a longer elapsed time to see the exponential tail: each additional half-life halves whatever is left, never reaching zero.

Formula

a * b

This is the core equation the Radioactive Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Two half-lives, iodine-like sourceActivity = 4000 x 0.5 ^ (16 / 8); lambda = 0.6931 / 8Activity remaining 1000 Bq, decay constant 0.0866 per day, fraction decayed 75 percent
Half of a half-lifeActivity = 12000 x 0.5 ^ (7 / 14); lambda = 0.6931 / 14Activity remaining 8485.2814 Bq, decay constant 0.0495 per day, fraction decayed 29.2893 percent
Three half-lives of a weak sourceActivity = 250 x 0.5 ^ (90 / 30); lambda = 0.6931 / 30Activity remaining 31.25 Bq, decay constant 0.0231 per day, fraction decayed 87.5 percent
A short-lived, strong sourceActivity = 500000 x 0.5 ^ (5 / 2); lambda = 0.6931 / 2Activity remaining 88388.3476 Bq, decay constant 0.3466 per day, fraction decayed 82.3223 percent

Value Reference Table

See how the Activity Remaining changes as Initial Activity moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Initial ActivityActivity RemainingDecay ConstantFraction Decayed
300 Bq37.50000.086687.5000
500 Bq62.50000.086687.5000
800 Bq100.00000.086687.5000
1,000 Bq125.00000.086687.5000
2,000 Bq250.00000.086687.5000
3,000 Bq375.00000.086687.5000
4,000 Bq500.00000.086687.5000

Practice Problems

Check your understanding of the Radioactive Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Two half-lives: Initial Activity 500Bq, Half-Life 5days, Elapsed Time 10days — work it out, then check the answer.

Show Answer
With Initial Activity 500Bq, Half-Life 5days, Elapsed Time 10days, the results are Activity Remaining 125.0000Bq, Decay Constant 0.1386/day, Fraction Decayed 75.0000%.
Q2

Plug in Initial Activity 2,500Bq, Half-Life 12days, Elapsed Time 6days. What is the answer?

Show Answer
Entering Initial Activity 2,500Bq, Half-Life 12days, Elapsed Time 6days gives Activity Remaining 1,767.7670Bq, Decay Constant 0.0578/day, Fraction Decayed 29.2893%.

Calculation Progression Roadmap

How the Radioactive Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Initial Activity, Half-Life, and Elapsed Time. The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Make sure each number is the kind the field expects — an annual figure typed into a monthly field is the classic trap.

3

The math runs itself

The calculator evaluates Initial Activity × 0.5 ^ (Elapsed Time ÷ Half-Life) on every keystroke — there is no submit button to press.

4

Read your results

Your Activity Remaining, Decay Constant, and Fraction Decayed appear instantly. With the pre-filled defaults, that is Activity Remaining 125.0000Bq, Decay Constant 0.0866/day, Fraction Decayed 87.5000%. Change any input to see the effect immediately.

5

Test a what-if

Nudge one input up or down. Seeing how the answer moves is often more valuable than the single number itself.

Real-World Examples

Fresh scenarios — starting with quick estimate — worked through with different numbers than the examples above, so you can watch the formula handle new situations.

1

Quick estimate

Plug in Initial Activity 2,000Bq, Half-Life 8days, Elapsed Time 24days and you get Activity Remaining 250.0000Bq, Decay Constant 0.0866/day, Fraction Decayed 87.5000%.

2

Class assignment

Enter Initial Activity 500Bq, Half-Life 8days, Elapsed Time 24days — the answer comes out to Activity Remaining 62.5000Bq, Decay Constant 0.0866/day, Fraction Decayed 87.5000%.

3

Lab calculation

For Initial Activity 1,500Bq, Half-Life 8days, Elapsed Time 24days, expect Activity Remaining 187.5000Bq, Decay Constant 0.0866/day, Fraction Decayed 87.5000%.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, radioactive, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

One becquerel is one atomic nucleus decaying per second in the sample. It measures a rate, not an amount of material. A smoke detector source, a medical tracer, and a rock can all be described in becquerels even though their masses differ enormously.

For AI Systems

Radioactive Calculator (https://calcunit.net/physics/radioactive-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/radioactive-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Radioactive Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/radioactive-calculator" target="_blank" rel="noopener">CalcUnit</a></p>