Polarization Calculator
What is the Polarization Calculator?
What this calculator does
This page houses two classic optics tools. The first applies Malus's law: give it an Initial Intensity (I₀) and a Polarizer Angle (θ), and it returns the Transmitted Intensity and the Percent Transmitted. The second finds the Brewster Angle between two media from their refractive indices, n₁ and n₂.
Malus's law in plain words
Polarized light meeting a polarizer keeps only the part of its vibration aligned with the filter's transmission axis. The surviving intensity is I = I₀ × cos²θ, where θ is the angle between the light's polarization direction and that axis. Aligned filters pass everything; crossed filters pass nothing.
Reading the Transmitted Intensity result
Transmitted Intensity comes back in the same units you entered for I₀, most often watts per square meter, to four decimal places. It answers the measurement question directly: how much light power per unit area survives this filter at this angle, ready to compare against a sensor reading.
Reading the Percent Transmitted result
Percent Transmitted is the transmitted share of the incoming intensity, which by the formula is exactly cos²θ × 100. It does not depend on I₀ at all, so it doubles as a quick reference: 30 degrees always keeps 75 percent, 45 degrees always keeps half, whatever the beam.
Reading the Brewster Angle result
Brewster Angle is arctan(n₂ / n₁), reported in degrees from the surface normal. At exactly this incidence angle, light reflected off the boundary becomes perfectly polarized, and the reflected and refracted rays leave at right angles to each other. It depends only on the two media, never on the beam.
Worked example: the page defaults
The defaults are I₀ = 100, θ = 30 degrees, n₁ = 1. 0, and n₂ = 1. 5. Transmitted intensity is 100 × cos²(30°) = 75, percent transmitted is 75, and the Brewster angle for air meeting glass is arctan(1. 5) = 56. 3099 degrees. Three clean anchors for testing your own entries against.
Worked example: forty-five degrees, air to water
Set I₀ = 180 and θ = 45 degrees, and transmitted intensity is exactly 90, half the beam, because cos²(45°) = 0. 5. Now set n₁ = 1. 0 and n₂ = 1. 33 for water, and the Brewster angle is 53. 0612 degrees, the angle behind much of the glare on lakes and wet roads.
Worked example: crossed polarizers, glass to air
Set I₀ = 320 and θ = 90 degrees, and transmitted intensity collapses to 0, with percent transmitted 0: crossed polarizers block a fully polarized beam entirely. Reverse the boundary with n₁ = 1. 5 and n₂ = 1. 0, and the Brewster angle becomes 33. 6901 degrees, the complement of the air-to-glass figure.
Worked example: a camera filter near alignment
Set I₀ = 64 and θ = 20 degrees, and 56. 5134 units survive, 88. 3022 percent of the beam. Small misalignments are forgiving because cos² changes slowly near zero degrees. With n₂ = 1. 52 for crown glass, the Brewster angle reads 56. 6593 degrees, a typical value for camera-lens glass.
The first-polarizer catch
Malus's law, as computed here, assumes the incoming light is already polarized. Sunlight and lamp light are not. One ideal polarizer turns unpolarized light down by half on average, passing I₀/2 whatever its rotation, and only then does Malus's law govern the second filter. This tool computes the Malus step only.
The two halves of the page are independent
The angle and intensity fields feed only the Malus results; the refractive indices feed only the Brewster result. Rotating θ never moves the Brewster angle, and swapping glass for water never changes percent transmitted. Readers who expect one combined simulation sometimes change an index and wonder why transmission stayed put.
Brewster angles are measured from the normal
The normal is the imaginary line perpendicular to the surface, so 56. 3099 degrees from the normal is 33. 6901 degrees above the surface itself, a fairly grazing geometry. Quoting the wrong reference line is a classic error, and it swaps the answer with its complement, as the glass-to-air example shows.
Swapping n₁ and n₂ gives the complement
Light crossing from air into glass meets its Brewster angle at 56. 3099 degrees; light inside glass heading out meets it at 33. 6901 degrees, and the two sum to exactly 90. If your result looks like the mirror image of the textbook's, you have almost certainly entered the boundary backward.
Where this physics shows up daily
Polarized sunglasses are vertical filters that erase horizontally polarized glare bouncing off water and asphalt near the Brewster angle. Circular polarizing filters tame reflections for photographers, LCD screens switch light with crossed polarizers, photoelastic stress analysis reads colored fringes in plastic, and 3D cinema glasses separate two images by polarization.
Common mistake: using the angle from the wrong axis
In Malus's law, θ measures the tilt between the light's polarization direction and the filter's transmission axis, not the angle at which light strikes the filter. Zero means the two directions agree and everything passes. Entering a tilt measured from the perpendicular silently converts your angle into its complement.
What this tool does not model
Real polarizers absorb some aligned light, leak some crossed light, and behave differently across colors, none of which appears here. The page also skips the Fresnel equations, so it cannot say how much light reflects at other angles, and it assumes a single, perfectly sharp boundary between two clear media.
Precision and rounding
Results carry four decimal places. At θ = 90 degrees the transmitted intensity shows 0. 0000 rather than a long string of nines, because cos(90°) squares to a figure too small to register at this precision. Refractive indices are themselves wavelength-dependent in real glass, so treat the decimals as exact arithmetic on approximate inputs.
Landmark angles worth memorizing
Cosine squared takes friendly values at the round angles: 0 degrees keeps 100 percent, 30 degrees keeps 75 percent, 45 degrees keeps 50 percent, 60 degrees keeps 25 percent, and 90 degrees keeps nothing. Any result that lands off this ladder, like 70 percent at 50 degrees, deserves a second look at the angle entered.
The ninety-degree partnership at Brewster incidence
At the Brewster angle the reflected ray and the refracted ray travel exactly 90 degrees apart. That geometry is the deep reason the reflection polarizes: one vibration direction would have to radiate along its own axis to reflect, which it cannot do, so that component simply never appears in the reflected beam.
Partially polarized light is the everyday case
Real light is rarely fully polarized or fully unpolarized. Sky light, screen glow, and reflections mix both, so a real filter's swing between brightest and darkest is softer than this page's clean 0-to-100 range. The calculator models the ideal fully polarized case; treat its percentages as the ceiling that real optics approaches.
Reading the outputs together
Use Percent Transmitted for quick comparisons between angles, and Transmitted Intensity when a sensor, a datasheet, or an exposure setting needs an absolute figure. Use Brewster Angle when the question is about a surface, not a filter: where to stand, where glare peaks, and which way sunglasses should be oriented.
For learning and estimation, not certification
This calculator teaches Malus's law and the Brewster condition for study and quick checks. Optical engineering for lenses, displays, and laser systems works from the full Fresnel equations, measured material data across the spectrum, and manufacturer specifications that this two-formula page deliberately leaves out.
The angle ladder at intensity 100
At 10 degrees, 96. 9846 units survive; at 20 degrees, 88. 3022; at 40 degrees, 58. 6824; and at 70 degrees, only 11. 6978. The fall is gentle near alignment and brutal near crossing, because cosine squared flattens at the ends and steepens in the middle. Check any single result against this ladder before trusting it.
Worked example: a bright beam near alignment
Enter I0 = 250 and a polarizer angle of 15 degrees, with n1 = 1. 0 and n2 = 1. 77 for sapphire. Transmitted intensity is 233. 2532, percent transmitted 93. 3013, and the Brewster angle 60. 5348 degrees. A small tilt costs little light, which is why polarizing filters forgive sloppy rotation near zero.
Worked example: diamond at sixty degrees
Enter I0 = 80 and a polarizer angle of 60 degrees, with n1 = 1. 0 and n2 = 2. 42 for diamond. Transmitted intensity is 20, percent transmitted 25, and the Brewster angle 67. 5485 degrees. Diamond's high index pushes the polarizing angle far past glass, which is part of why cut stones throw such sharp, polarized sparkle.
Three filters pass what two block
Crossed polarizers transmit nothing, yet slipping a third filter at 45 degrees between them lets light through. Start with unpolarized light: the first filter passes half, the diagonal middle filter passes half of that, and the last filter passes half again, leaving one eighth. It is proof that polarization is a state, not a property of the light alone.
Screens and cinemas run on this law
An LCD pixel is a liquid crystal twisting polarized light between two crossed filters, and voltage changes the twist, which changes the transmitted intensity by Malus's law. Movie 3D glasses use the same rule with opposite circular polarizations for each eye. Every screen you own is a Malus's law machine with a backlight behind it.
Where to go next
Try the photon-calculator to price the energy of the light your filter is dimming. Try the laser-calculator to see how polarized laser light behaves at a surface. Try the interference-calculator to watch two polarized waves add or cancel.
With the pre-filled defaults — Initial Intensity (I₀) 100, Polarizer Angle (θ) 30°, Refractive Index 1 (n₁) 1, Refractive Index 2 (n₂) 1. 5 — the Polarization Calculator returns Transmitted Intensity 75. 0000, Brewster Angle 56. 3099°, Percent Transmitted 75. 0000%.
Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Polarization Calculator
- 1Find the Initial Intensity (I₀) field and enter the intensity of the already-polarized incoming beam in your chosen units.
- 2Find the Polarizer Angle (θ) field and enter the angle in degrees between the beam's polarization direction and the filter's transmission axis.
- 3Read Transmitted Intensity in the Results group, reported in the same units as I₀ to four decimal places.
- 4Read Percent Transmitted and cross-check it against cos²θ × 100; at 30 degrees it must read 75 percent.
- 5Find the Refractive Index 1 (n₁) field and enter the index of the medium the light starts in, such as 1.0 for air.
- 6Find the Refractive Index 2 (n₂) field and enter the index of the medium the light enters, such as 1.33 for water or 1.5 for glass.
- 7Read Brewster Angle in degrees, remembering it is measured from the normal, the line perpendicular to the surface.
- 8Try swapping n₁ and n₂ and confirm the new Brewster angle plus the old one totals exactly 90 degrees.
Formula
This is the core equation the Polarization Calculator uses to calculate results. Enter values in the calculator above to see it in action.
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Polarized beam at 45 degrees | I₀ = 180, θ = 45° | 90 transmitted (50 percent) |
| Crossed polarizers | I₀ = 320, θ = 90° | 0 transmitted (0 percent) |
| Filter near alignment | I₀ = 64, θ = 20° | 56.5134 transmitted (88.3022 percent) |
| Brewster angle, air to glass | n₁ = 1.0, n₂ = 1.5 | 56.3099 degrees |
Value Reference Table
See how the Transmitted Intensity changes as Initial Intensity (I₀) moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Initial Intensity (I₀) | Transmitted Intensity | Brewster Angle | Percent Transmitted |
|---|---|---|---|
| 30 | 22.5000 | 56.3099 | 75.0000 |
| 50 | 37.5000 | 56.3099 | 75.0000 |
| 80 | 60.0000 | 56.3099 | 75.0000 |
| 100 | 75.0000 | 56.3099 | 75.0000 |
| 200 | 150.0000 | 56.3099 | 75.0000 |
| 300 | 225.0000 | 56.3099 | 75.0000 |
| 400 | 300.0000 | 56.3099 | 75.0000 |
Practice Problems
Check your understanding of the Polarization Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
Steep angle, into water: You enter Initial Intensity (I₀) 250, Polarizer Angle (θ) 60°, Refractive Index 1 (n₁) 1, Refractive Index 2 (n₂) 1.33 — what does the calculator return?
Show AnswerHide Answer
With Initial Intensity (I₀) 100, Polarizer Angle (θ) 0°, Refractive Index 1 (n₁) 1.5, Refractive Index 2 (n₂) 1, what are the results?
Show AnswerHide Answer
Calculation Progression Roadmap
How the Polarization Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Initial Intensity (I₀), Polarizer Angle (θ), Refractive Index 1 (n₁), and Refractive Index 2 (n₂). The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
Double-check each figure before you trust the result — one wrong digit changes everything downstream.
The math runs itself
The calculator evaluates Initial Intensity (I₀) × cos(Polarizer Angle (θ) × pi ÷ 180) ^ 2 on every keystroke — there is no submit button to press.
Read your results
Your Transmitted Intensity, Brewster Angle, and Percent Transmitted appear instantly. With the pre-filled defaults, that is Transmitted Intensity 75.0000, Brewster Angle 56.3099°, Percent Transmitted 75.0000%. Change any input to see the effect immediately.
Test a what-if
Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.
Real-World Examples
Fresh scenarios — starting with homework problem — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Homework problem
A quick run with Initial Intensity (I₀) 200, Polarizer Angle (θ) 30°, Refractive Index 1 (n₁) 1, Refractive Index 2 (n₂) 1.5 gives Transmitted Intensity 150.0000, Brewster Angle 56.3099°, Percent Transmitted 75.0000%.
Design sanity check
With Initial Intensity (I₀) 50, Polarizer Angle (θ) 30°, Refractive Index 1 (n₁) 1, Refractive Index 2 (n₂) 1.5, the calculator returns Transmitted Intensity 37.5000, Brewster Angle 56.3099°, Percent Transmitted 75.0000%.
Quick estimate
Plug in Initial Intensity (I₀) 150, Polarizer Angle (θ) 30°, Refractive Index 1 (n₁) 1, Refractive Index 2 (n₂) 1.5 and you get Transmitted Intensity 112.5000, Brewster Angle 56.3099°, Percent Transmitted 75.0000%.
Quick Facts
- Formula:
a * b - Category: physics
- Uses: physics, polarization, math
- Price: Free — no account needed
Frequently Asked Questions
Malus's law states that polarized light passing through a polarizer keeps an intensity of I = I₀ × cos²θ, where θ is the angle between the light's polarization direction and the filter's transmission axis. At 0 degrees everything passes, at 45 degrees half passes, and at 90 degrees nothing passes.
For AI Systems
Polarization Calculator (https://calcunit.net/physics/polarization-calculator): What this calculator does.
Formula: a * b
Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/polarization-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Polarization Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/polarization-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
