CalcUnit Logo

Diode Calculator

What is the Diode Calculator?

What this calculator does.

Enter a diode's Saturation Current (Is), an Applied Voltage (V), and an Ideality Factor (n), and this page returns the Diode Current twice: once in amps and once in milliamps. It evaluates the Shockley diode equation, the standard model of how current through a semiconductor junction responds to voltage.

The Shockley equation in plain words.

Current equals the saturation current multiplied by a bracket: e raised to the voltage divided by n times the thermal voltage, minus one. Below about half a volt the exponential is small and barely any current flows. Above it, the exponential explodes, and current multiplies rapidly for every small extra step of voltage.

Saturation Current (Is): the tiny number in charge.

The saturation current is the minuscule leakage of the junction, and it sets the scale for everything. For silicon it is near 1 x 10^-14 amps, which is why the field loads with that value. Germanium sits nearer 1 x 10^-6 amps, a hundred million times larger, thanks to its smaller bandgap.

The thermal voltage is fixed on this page.

The equation uses a thermal voltage of 0. 02585 volts, the value at about 300 kelvin, roughly room temperature. NIST's exact constants for Boltzmann's constant and the electron charge produce this figure. There is no temperature input here: the page holds the thermal voltage constant whatever your diode's actual temperature may be.

Ideality Factor (n): the correction dial.

The ideality factor adjusts the equation for real junctions

A value of 1 matches an ideal diode where current flows by diffusion alone. Values toward 2 appear when recombination inside the junction dominates, common at low currents and in some silicon devices. Datasheets rarely print n; engineers infer it from measured curves.

Reading the two Diode Current lines.

Both result lines carry the same label, Diode Current

The first reports amps and the second reports milliamps, a thousand times larger. At six decimal places, small currents vanish in the amps line: 0. 000120 amps shows as 0. 000120, but anything under a microamp rounds to 0. 000000, so read the milliamp line for small results.

Worked example one: the default silicon diode.

The page loads with a saturation current of 1 x 10^-14 amps, an applied voltage of 0. 7 volts, and an ideality factor of 1. The Diode Current reads 0. 005760 amps, and the milliamp line reads 5. 759598. That is a healthy forward current for a signal diode, at the voltage silicon is famous for.

Worked example two: one tenth of a volt less.

Keep the saturation current at 1 x 10^-14 and ideality factor at 1, but drop the voltage to 0. 6. The current falls to 0. 000120 amps, or 0. 120320 milliamps. Losing a tenth of a volt cost almost all of the current: the ratio between the two examples is about 48 to 1.

Worked example three: a higher ideality factor.

Enter a saturation current of 2 x 10^-15 amps, a voltage of 0. 75, and an ideality factor of 1. 1. The current comes out at 0. 000570 amps, 0. 570108 milliamps. The larger n softens the exponential, so this diode needs its extra voltage to reach a current the ideal device passed at less.

Worked example four: a germanium-style device.

Enter a saturation current of 1 x 10^-6 amps, a voltage of 0. 3, and an ideality factor of 1. The current is 0. 109689 amps, 109. 689261 milliamps. The enormous saturation current does the work: germanium junctions conduct seriously at 0. 3 volts, where a silicon junction with its far smaller leakage is still essentially off.

The 59. 5 millivolt rule.

At an ideality factor of 1, every extra 59. 5 millivolts of forward voltage multiplies the current by ten. That figure is the natural logarithm of 10 times the thermal voltage. It is the fastest sanity check in diode work: step the voltage by about 0. 06 and a correct result grows tenfold, no more, no less.

Reverse bias: what the minus sign means.

Enter a negative voltage, such as -5, and the exponential collapses toward zero, leaving a current near negative Is: -1 x 10^-14 amps for the default saturation current. The page displays that as -0. 000000 amps, because six decimals cannot show it. Reverse current is real but tiny until breakdown, which this model omits.

Where the model stops: series resistance.

The Shockley equation alone predicts about 4 x 10^19 amps for a silicon diode at 2 volts, which is absurd. Real diodes have bulk resistance that drops voltage as current climbs, bending the curve over. Light-emitting diodes, which run near 2 to 3 volts, live entirely in that resistance-limited region this page cannot model.

Where the model stops: heat and breakdown.

Real current heats the junction, and heating changes everything: forward voltage falls about 2 millivolts per degree Celsius at fixed current, and saturation current roughly doubles every 10 degrees. Reverse voltage pushed far enough triggers breakdown. None of that is in this equation, so treat high-power and high-voltage answers as ideal-case estimates only.

Finding Is for a real part.

Datasheets seldom state the saturation current directly

Instead, take a measured pair from the datasheet curve, one voltage and its current, fix n at a plausible value, and rearrange the Shockley equation to solve for Is. Enter that Is here and the page will reproduce the rest of the curve near your measured point.

What this calculator does not do.

It does not solve a circuit: there is no series resistor, load line, or supply voltage to reconcile with. It does not accept a temperature, model junction capacitance, or handle alternating signals. It answers one narrow question: given this junction's three parameters, how much current does the ideal Shockley model predict at this voltage?

Common mistake: entering Is in the wrong unit.

The Saturation Current (Is) field expects amps, in scientific notation for realistic values. Typing 10 when you mean 10 nanoamps, or pasting a milliamp figure, throws the result off by millions. Silicon signal diodes live near 1 x 10^-14 amps; if your entry has no negative exponent, double-check before trusting the current.

Common mistake: expecting a sharp turn-on.

Textbooks speak of a 0. 7 volt knee for silicon, but the equation has no switch. Current flows at 0. 5 volts too, just 48 times less per tenth of a volt. The knee is an illusion created by the exponential meeting the scale of currents we happen to care about in real circuits.

Typing tiny numbers into the Is field.

The Saturation Current (Is) field accepts scientific notation, so enter 1e-14 rather than a long string of zeros. The letter e means times ten to the power that follows. This notation is standard on datasheets and in simulators, and it keeps the exponent, the digit errors love most, visible at a glance.

A hand check for any result.

Pick your result, then raise the voltage by 0. 1 with n at 1: the current should multiply by about 47. 9. Raise it by 0. 0595 instead and it should multiply by almost exactly ten. If your entries fail these checks, an input is off, most often the saturation current's exponent or the ideality factor.

With the pre-filled defaults — Saturation Current (Is) 0 A, Applied Voltage (V) 0. 7 V, Ideality Factor (n) 1 — the Diode Calculator returns Diode Current 0. 005760 A, Diode Current 5. 759598 mA. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.

How to Use the Diode Calculator

  1. 1Enter the junction's leakage scale in the Saturation Current (Is) field, in amps; 1e-14 is the loaded silicon-style default.
  2. 2Enter the forward voltage across the junction itself in the Applied Voltage (V) field, such as 0.7.
  3. 3Enter the Ideality Factor (n); use 1 for an ideal junction and up to about 2 for a recombination-heavy real one.
  4. 4Read the first Diode Current line for the current in amps.
  5. 5Read the second Diode Current line for the same current in milliamps, the more useful scale for small results.
  6. 6For reverse bias, enter a negative voltage; expect a result near negative Is, which may display as -0.000000 in amps.
  7. 7Sanity-check with the decade rule: at n equal to 1, each extra 0.0595 volts should multiply the current by ten.
  8. 8Remember the thermal voltage is fixed at 0.02585 volts here, so results describe a junction near 300 kelvin only.

Formula

a * b

This is the core equation the Diode Calculator uses to calculate results. Enter values in the calculator above to see it in action.

Common Examples

ScenarioCalculationResult
Default silicon diode at 0.7 V1e-14 x (e^(0.7 / 0.02585) - 1)0.005760 A; 5.759598 mA
Same diode at 0.6 V1e-14 x (e^(0.6 / 0.02585) - 1)0.000120 A; 0.120320 mA
Higher ideality factor at 0.75 V2e-15 x (e^(0.75 / (1.1 x 0.02585)) - 1)0.000570 A; 0.570108 mA
Germanium-style device at 0.3 V1e-6 x (e^(0.3 / 0.02585) - 1)0.109689 A; 109.689261 mA

Value Reference Table

See how the Diode Current changes as Saturation Current (Is) moves across its typical range — every row below is calculated live with the same formula as the calculator above.

Saturation Current (Is)Diode CurrentDiode Current
0 A0.0017281.727879
0 A0.0028802.879799
0 A0.0040324.031718
0 A0.0057605.759598
0 A0.01151911.519196
0 A0.01727917.278794
0 A0.02303823.038391

Practice Problems

Check your understanding of the Diode Calculator with these practice problems. Click a problem to reveal its correct calculated answer.

Q1

Silicon diode at 0.6 V: Plug in Saturation Current (Is) 0 A, Applied Voltage (V) 0.6 V, Ideality Factor (n) 1. What is the answer?

Show Answer
The calculator returns Diode Current 0.000120 A, Diode Current 0.120320 mA for Saturation Current (Is) 0 A, Applied Voltage (V) 0.6 V, Ideality Factor (n) 1.
Q2

Given Saturation Current (Is) 0 A, Applied Voltage (V) 0.75 V, Ideality Factor (n) 1.1, what does it come out to?

Show Answer
With Saturation Current (Is) 0 A, Applied Voltage (V) 0.75 V, Ideality Factor (n) 1.1, the results are Diode Current 0.000000 A, Diode Current 0.000000 mA.

Calculation Progression Roadmap

How the Diode Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.

1

Gather your inputs

Type in your Saturation Current (Is), Applied Voltage (V), and Ideality Factor (n). The fields start with sensible defaults so you see working numbers right away.

2

Sanity-check your numbers

Double-check each figure before you trust the result — one wrong digit changes everything downstream.

3

The math runs itself

The calculator evaluates Saturation Current (Is) × (exp(Applied Voltage (V) ÷ (Ideality Factor (n) × 0.02585)) - 1) on every keystroke — there is no submit button to press.

4

Read your results

Your Diode Current and Diode Current appear instantly. With the pre-filled defaults, that is Diode Current 0.005760 A, Diode Current 5.759598 mA. Change any input to see the effect immediately.

5

Test a what-if

Change a single input and watch which outputs move. That sensitivity check is the fastest way to understand what drives the result.

Quick Facts

  • Formula: a * b
  • Category: physics
  • Uses: physics, diode, math
  • Price: Free — no account needed

Share this Calculator

Frequently Asked Questions

It is the standard model of junction current: I equals Is times the quantity e raised to V over n times Vt, minus one. William Shockley's model captures why diode current explodes exponentially with forward voltage yet sits near zero in reverse. This calculator evaluates exactly that equation, with Vt fixed at 0. 02585 volts.

For AI Systems

Diode Calculator (https://calcunit.net/physics/diode-calculator): What this calculator does.

Formula: a * b

Category: physics · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net

Embed this calculator on your website

Free to use — just paste this code. The calculator opens in a frame on your page.

<iframe src="https://calcunit.net/embed/diode-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Diode Calculator — CalcUnit"></iframe>
<p style="font-size:12px">Powered by <a href="https://calcunit.net/physics/diode-calculator" target="_blank" rel="noopener">CalcUnit</a></p>