Frequency Response Calculator
What is the Frequency Response Calculator?
What this page does
Give it a resistor, a capacitor, and a signal frequency, and this page works out how a simple RC low-pass filter treats that signal. It returns the filter cutoff frequency, the gain at your frequency, that gain in decibels, and the phase shift the filter introduces.
The honest scope, up front
This page models exactly one circuit: a first-order RC low-pass filter, one resistor and one capacitor, at one single frequency. It cannot do high-pass filters, LC circuits, multi-stage filters, or a swept graph.
When to look elsewhere
If your circuit is anything more than a resistor feeding a capacitor to ground, this page is a starting estimate, not the answer.
The three inputs it asks for
Resistance R is in ohms, Capacitance C is in farads, and Input Frequency is in hertz. The page opens with 1000 ohms, 0. 000001 farads, and 100 hertz filled in. That capacitance, one microfarad written out in farads, is where most entry mistakes happen, so check the string of zeros carefully.
Worked example: the page defaults
With 1000 ohms and one microfarad, the cutoff frequency is 159. 1549 hertz. At the default 100 hertz input, safely below cutoff, the gain is 0. 8467, the gain in decibels is negative 1. 4451, and the phase shift is negative 32. 1419 degrees. Most of the signal survives, slightly delayed.
The cutoff frequency
The cutoff is 1 divided by 2 pi times R times C. It is the dividing line of the filter: frequencies well below it pass almost untouched, and frequencies well above it fade away. Double the resistance or the capacitance and the cutoff halves, because the capacitor takes twice as long to charge.
What happens exactly at cutoff
Feed the filter a signal at its own cutoff frequency and the gain is always 0. 7071, the decibel gain is negative 3. 0103, and the phase shift is exactly negative 45 degrees.
Why that point matters
That 0. 7071 figure is the famous minus 3 decibel point, where the output power has fallen to one half of the input power.
The gain line
Gain at Input Frequency is a voltage ratio between zero and one for this filter. A gain of 1 would mean the signal passes unchanged; 0. 5 means the output swings half as far as the input. This filter can never amplify, so a gain above 1 from these fields means an entry error somewhere.
The gain in decibels
The Gain line restates the same ratio in decibels: 20 times the base-10 logarithm of the gain. Zero decibels means unchanged, negative values mean the signal shrank, and every drop of about 6 decibels halves the voltage again. Audio and radio engineers live in this unit because it turns huge ratios into handy numbers.
The phase shift
A capacitor delays the signal, so the output wave peaks a little after the input wave. The Phase Shift line reports that lag in degrees, always negative for this circuit because the output trails the input.
How the lag grows
The lag is near zero far below cutoff, negative 45 degrees at cutoff, and it creeps toward negative 90 degrees far above.
Worked example: audio tone control values
Take 10000 ohms and 0. 1 microfarads, which is 0. 0000001 farads, at 50 hertz. The cutoff is again 159. 1549 hertz, because the resistance-times-capacitance product matches the default pair.
The numbers at 50 hertz
The gain is 0. 954, the decibel gain is negative 0. 4088, and the phase shift is negative 17. 4406 degrees. Low audio tones pass nearly intact.
Worked example: well past the cutoff
Take 470 ohms and one microfarad at 1000 hertz. The cutoff is 338. 6275 hertz, so the signal sits almost three times above it.
What remains of the signal
The gain falls to 0. 3207, the decibel gain to negative 9. 877, and the phase shift to negative 71. 2925 degrees. Roughly two thirds of the signal voltage is gone.
Worked example: a larger capacitor swap
Take 4700 ohms and 0. 1 microfarads, again 0. 0000001 farads, at 200 hertz. The cutoff is the same 338. 6275 hertz, since the product of R and C is unchanged from the previous example.
The numbers at 200 hertz
The gain is 0. 861, the decibel gain is negative 1. 2996, and the phase shift is negative 30. 5669 degrees.
Entering capacitance without tears
Capacitors are sold in microfarads and nanofarads, but this field wants farads. One microfarad is 0. 000001, a tenth of a microfarad is 0. 0000001, and one nanofarad is 0. 000000001. If your cutoff comes out a thousand times higher or lower than expected, a slipped decimal in this field is the usual culprit.
How fast the signal fades above cutoff
Past the cutoff, this single-stage filter rolls off at about 20 decibels per decade. At ten times the cutoff frequency the gain is roughly 0. 0995, about a tenth of the input.
The price of one stage
That gentle slope is the price of a one-resistor, one-capacitor design; steeper filtering needs more stages or a different circuit entirely.
Zero components give zero answers
Set the resistance or the capacitance to zero and every output line collapses to zero: cutoff zero, gain zero, decibels zero, phase zero. Those zeros are placeholder guards in the formulas, not physics. A real zero-ohm path would pass everything, so treat the all-zero result as the page declining to answer.
Choosing values that behave
Standard capacitor values jump in coarse steps, so hitting an exact cutoff is rare in real builds. Pick the nearest standard capacitor, then trim the resistance to land the cutoff where you need it, because resistors come in finer steps. Rerun the page with both candidate pairs and compare the gain at your frequency.
Checking the result by hand
The capacitor reactance at your frequency is 1 divided by 2 pi times f times C, and the circuit is a voltage divider between the resistor and that reactance.
The divider formula
Gain equals reactance divided by the square root of R squared plus reactance squared. Reaching the same number by that route confirms the page was fed the right values.
What this page cannot do
There is no frequency sweep, no graph, no second stage, and no component tolerance. Real capacitors drift by 10 or 20 percent from their printed value, and the page assumes perfection. It also models an unloaded filter; whatever you connect to the output changes the effective resistance and shifts the real cutoff.
Where this filter lives
RC low-pass pairs sit in guitar tone knobs, in the smoothing stage after a rectifier, in anti-aliasing paths before analog-to-digital converters, and in simple hiss cutters for small speakers.
One tone at a time
In each job the same four numbers on this page, cutoff, gain, decibels, and phase, describe what the circuit will do to one tone.
With the pre-filled defaults — Resistance R 1,000Ω, Capacitance C 0. 000001F, Input Frequency 100Hz — the Frequency Response Calculator returns Cutoff Frequency 159. 1549Hz, Gain at Input Frequency 0. 8467, Gain -1. 4451dB, Phase Shift -32. 1419°. Change any input and those results update instantly, so you can see exactly how each number you enter moves the answer.
How to Use the Frequency Response Calculator
- 1Enter your resistor value, in ohms, in the Resistance R field.
- 2Enter your capacitor value in the Capacitance C field, converting microfarads to farads first (1 µF = 0.000001 F).
- 3Enter the signal frequency you care about, in hertz, in the Input Frequency field.
- 4Read the Cutoff Frequency line to see where this filter starts turning signals down.
- 5Compare your input frequency with the cutoff: below it passes, above it fades.
- 6Read Gain at Input Frequency for the surviving fraction of the signal voltage.
- 7Read the Gain line in decibels for the same change in engineering units.
- 8Read Phase Shift to see how many degrees the output lags behind the input.
Formula
This is the core equation the Frequency Response Calculator uses to calculate results. Enter values in the calculator above to see it in action.
Common Examples
| Scenario | Calculation | Result |
|---|---|---|
| Page defaults: 1 kΩ and 1 µF at 100 Hz | Cutoff = 1 ÷ (2π × 1000 × 0.000001) = 159.1549 Hz; gain = 1 ÷ √(1 + (100 ÷ 159.1549)²) | Gain 0.8467, gain −1.4451 dB, phase shift −32.1419° |
| 10 kΩ and 0.1 µF at 50 Hz | Cutoff = 1 ÷ (2π × 10000 × 0.0000001) = 159.1549 Hz; frequency ratio 50 ÷ 159.1549 = 0.3142 | Gain 0.954, gain −0.4088 dB, phase shift −17.4406° |
| 470 Ω and 1 µF at 1 kHz | Cutoff = 1 ÷ (2π × 470 × 0.000001) = 338.6275 Hz; frequency ratio 1000 ÷ 338.6275 = 2.9531 | Gain 0.3207, gain −9.877 dB, phase shift −71.2925° |
| 4.7 kΩ and 0.1 µF at 200 Hz | Cutoff = 1 ÷ (2π × 4700 × 0.0000001) = 338.6275 Hz; frequency ratio 200 ÷ 338.6275 = 0.5906 | Gain 0.861, gain −1.2996 dB, phase shift −30.5669° |
Value Reference Table
See how the Cutoff Frequency changes as Resistance R moves across its typical range — every row below is calculated live with the same formula as the calculator above.
| Resistance R | Cutoff Frequency | Gain at Input Frequency | Gain | Phase Shift |
|---|---|---|---|---|
| 300 Ω | 530.5165 | 0.9827 | -0.1516 | -10.6747 |
| 500 Ω | 318.3099 | 0.9540 | -0.4088 | -17.4406 |
| 800 Ω | 198.9437 | 0.8935 | -0.9783 | -26.6866 |
| 1,000 Ω | 159.1549 | 0.8467 | -1.4451 | -32.1419 |
| 2,000 Ω | 79.5775 | 0.6227 | -4.1147 | -51.4881 |
| 3,000 Ω | 53.0516 | 0.4686 | -6.5830 | -62.0533 |
| 4,000 Ω | 39.7887 | 0.3697 | -8.6431 | -68.3030 |
Practice Problems
Check your understanding of the Frequency Response Calculator with these practice problems. Click a problem to reveal its correct calculated answer.
10 kΩ and 0.1 µF at 50 Hz: Plug in Resistance R 10,000Ω, Capacitance C 0F, Input Frequency 50Hz. What is the answer?
Show AnswerHide Answer
Given Resistance R 587.5Ω, Capacitance C 0.000001F, Input Frequency 1,000Hz, what does it come out to?
Show AnswerHide Answer
Calculation Progression Roadmap
How the Frequency Response Calculator turns your inputs into a result, step by step — from the values you type to the answer you read.
Gather your inputs
Type in your Resistance R, Capacitance C, and Input Frequency. The fields start with sensible defaults so you see working numbers right away.
Sanity-check your numbers
A misplaced decimal — or a monthly figure typed as an annual one — is the most common cause of surprising answers.
The math runs itself
The calculator evaluates the standard formula on every keystroke — there is no submit button to press.
Read your results
Your Cutoff Frequency, Gain at Input Frequency, Gain, and Phase Shift appear instantly. With the pre-filled defaults, that is Cutoff Frequency 159.1549Hz, Gain at Input Frequency 0.8467, Gain -1.4451dB, Phase Shift -32.1419°. Change any input to see the effect immediately.
Test a what-if
Try a bigger and a smaller value for one input. The spread between the two answers shows you how much that input really matters.
Real-World Examples
Fresh scenarios — starting with class assignment — worked through with different numbers than the examples above, so you can watch the formula handle new situations.
Class assignment
Enter Resistance R 2,000Ω, Capacitance C 0.000001F, Input Frequency 100Hz — the answer comes out to Cutoff Frequency 79.5775Hz, Gain at Input Frequency 0.6227, Gain -4.1147dB, Phase Shift -51.4881°.
Homework check
For Resistance R 500Ω, Capacitance C 0.000001F, Input Frequency 100Hz, expect Cutoff Frequency 318.3099Hz, Gain at Input Frequency 0.9540, Gain -0.4088dB, Phase Shift -17.4406°.
Double-checking a spreadsheet
A quick run with Resistance R 1,500Ω, Capacitance C 0.000001F, Input Frequency 100Hz gives Cutoff Frequency 106.1033Hz, Gain at Input Frequency 0.7277, Gain -2.7606dB, Phase Shift -43.3038°.
Quick Facts
- Formula:
a * b - Category: math
- Uses: math, frequency response, math
- Price: Free — no account needed
Frequently Asked Questions
It is the frequency where the filter stops passing a signal cleanly and starts turning it down in earnest, computed as 1 divided by 2 pi times the resistance times the capacitance. At the cutoff itself the gain is 0. 7071, the output power is halved, and engineers call it the minus 3 decibel point.
For AI Systems
Frequency Response Calculator (https://calcunit.net/math/frequency-response-calculator): What this page does.
Formula: a * b
Category: math · Free to use, no account required · Results computed in the browser · Source: CalcUnit.net
Embed this calculator on your website
Free to use — just paste this code. The calculator opens in a frame on your page.
<iframe src="https://calcunit.net/embed/frequency-response-calculator/" width="100%" height="560" style="border:1px solid #DEE2EA;border-radius:12px" loading="lazy" title="Frequency Response Calculator — CalcUnit"></iframe> <p style="font-size:12px">Powered by <a href="https://calcunit.net/math/frequency-response-calculator" target="_blank" rel="noopener">CalcUnit</a></p>
